SSL
main menu:
on line store:
welding demos:
cutting demos:
 

Content on this page requires a newer version of Adobe Flash Player.

Get Adobe Flash player
DHC 2000 Torch Replacement Parts - Accessories - Welding Supplies

DHC 2000 Accessories

#00Tip

  • For Jewelry or 26-28 gauge sheet metal.
  • Use anytime a VERY SMALL Flame is needed like for jewelry work or small prototype work or models.
  • Identify by knurl pattern.

$20.00 each + sales tax (NC/SC only)

#1/2 Tip

  • For Automotive Sheet metal (18-22) gauge
  • Also works well on .030 chromoly and EMT (conduit) Our most popular option
  • Identify by small single groove (smaller than #1)

$20.00 each + sales tax (NC/SC only)

#1.5Tip

  • NEW ACCESSORY
  • This tip is for 1/8-3/16 welding
  • If the #1 tip is too small or the #2 tip is too large this one will be just right.

$20.00 each + sales tax (NC/SC only)
#2.5Tip
  • For Heavy Duty Welding like Engine Blocks & Cylinder Heads
  • For thick aluminum or cast iron (3/8" to 1'')
  • Identify by parallel ribs.

$20.00 each + sales tax (NC/SC only)
Air-acetylene tip
  • Air-Acetylene tip uses only acetylene, NO Oxygen
  • Used for Body Solder (Lead work) on body panels and soldering of copper pipe.
  • Works like a Turbo or propane torch.
  • Works well for thawing frozen water pipes or general purpose heating when a lower temperature very soft bushy flame is needed.
     


$35.00 each + sales tax (NC/SC only)

 6"Straight Welding tip Extension

  • For confined areas such as ports in cylinder heads or to move your hand back from the heat when welding heavy materials

 

$25.00 each + sales tax (NC/SC only)
 
Curved Welding Extension
  • For Overhead Welding such as exhaust , roll cages ,aircraft frames and in HVAC & Plumbing applications
  • About "6" long with 135 degree bend

$25.00 each + sales tax (NC/SC only)
Master Pro Pac

Includes the following welding tips and accessories:
total value $145.00

  • #00, #1.5 and #2.5 Tips
  • Air-acetylene Tip
  • Curved Extension
  • Straight Extension

$99.00 each + sales tax (NC/SC only)

Rosebud Heating Tip

For heating large areas and bending thick metal.

For all DHC 2000, Dillon and Henrob 2000 torches,





 

 

 

$105.00 each + sales tax (NC/SC only)
Hoses
  • Light weight 3/16 in. 50% lighter than standard 1/4 in. hose
  • Twin welding hose grade (R) made in USA  
  • Standard "B" fittings

12.5 ft length
$20.00 each + sales tax (NC/SC only)

25 ft length
$30.00 each + sales tax (NC/SC only)
Quick Disconnects
  • Comes with one each: acetylene male, acetylene female, oxygen male, oxygen female
  • One set is required for each torch to be connected

Torch to Hose -1 set
 $65.00 each + sales tax (NC/SC only)

Torch to Hose - 2 sets
 $125.00 each + sales tax (NC/SC only)

Hose to Hose -1 set
$65.00 each + sales tax (NC/SC only)

Hose to Hose - 2 sets
 $125.00 each + sales tax (NC/SC only)

Regulators to Hose -1 set
 $65.00 each + sales tax (NC/SC only)

Regulators to Hose - 2 sets
 $125.00 each + sales tax (NC/SC only)
Welding Supplies

 

Cast Iron Welding Rod (Harris Products KASTWELD 111)

A square oxy-fuel, high quality, low cost, cast iron welding rod. A precisely balanced ratio of silicon and carbon assures a fluid weld metal deposit with similar physical properties to gray cast iron. Kastweld deposits are easily machined and closely match the color of the base metal. It is excellent for cast iron fabrication; repairing foundry defects; and for filling in or building up new or worn castings. Conforms to AWS A5.15 grade RCI.


$25.00 per lb. + sales tax (NC/SC only)

 

Cast Iron Welding Flux

  • Required for welding Cast Iron or Cast Steel
  • Must use with Proper LENS
  • 1 LB. can



$20.00 each + sales tax (NC/SC only)

 

Aluminum Welding Flux

  • Required for aluminum welding
  • Must use With Proper LENS (see below for choices)

 

$15.00 each + sales tax (NC/SC only)
DHC 2000 Original Replacement Parts

#0 Welding Tip
$20.00 each + sales tax (NC/SC only)

#1 Welding Tip
$20.00 each + sales tax (NC/SC only)

#2 Welding Tip
$20.00 each + sales tax (NC/SC only)

#3 Welding Tip
 $20.00 each + sales tax (NC/SC only)

Cutting Tip
 $20.00 each + sales tax (NC/SC only)

Shank, oxy-acetylene (Tip screws on this)
$20.00 each + sales tax (NC/SC only)

Plug (Where cutting attachment screws in)
$20.00 each + sales tax (NC/SC only)

Wrench
 $8.00 each + sales tax (NC/SC only)

Tip cleaner Set
$8.00 each + sales tax (NC/SC only)

Valve OXYGEN (Blue knob)
$22.00 each + sales tax (NC/SC only)

Valve ACETYLENE (Red knob)
$22.00 each + sales tax (NC/SC only)

Over cutter Assembly
 $40.00 each + sales tax (NC/SC only)

Under cutter Assembly
 $40.00 each + sales tax (NC/SC only)

Cutting guide (Training wheels)
$40.00 each + sales tax (NC/SC only)

Manual with J&S supplement
 $10.00 each + sales tax (NC/SC only)

Carry case
 $28.00 each + sales tax (NC/SC only)

Check Valves
$20.00 each + sales tax (NC/SC only)

Instructional Videos

Video (Instructional, VHS) ***
$25.00 each + sales tax (NC/SC only)

Video (Instructional, DVD) ***
$25.00 each + sales tax (NC/SC only)

*** This video is the one supplied with our bonus kit and can be seen in our streaming video library.  Available only from J&S Enterprises.  30 minutes.
 

Additional Products : Cobra IR Lenses